
#REDIRECT Hard disk
A hard disk (or "hard disc" or "hard drive" or "hard disk drive") is a computer data storage device that stores data on rotating magnetic surfaces. ==Mechanics== A hard disk uses rigid rotating hard disk platter (disks). It stores and retrieves digital data from a planar magnetic surface. Information is written to the disk by transmitting an electromagnetic flux through an antenna or ''write head'' that is very close to a magnetic material, which in turn changes its polarization due to the flux. The information can be read back in a reverse manner, as the magnetic fields cause electrical change in the coil or ''read head'' that passes over it. A typical hard disk drive design consists of a central axis or spindle upon which the platters spin at a constant speed. Moving along and between the platters on a common armature are the disk read-and-write head, with one head for each platter face. The armature moves the heads radially across the platters as they spin, allowing each head access to the entirety of the platter. The associated electronics control the movement of the read-write armature and the rotation of the disk, and perform reads and writes on demand from the disk controller. Modern drive electronics are capable of scheduling reads and writes efficiently across the disk, and of remapping sectors of the disk which have failed. Also, most major hard drive and motherboard vendors now support Self-Monitoring, Analysis and Reporting Technology technology, by which impending failures can often be predicted, allowing the user to be alerted in time to prevent data loss. The (mostly) sealed enclosure protects the drive internals from dust, condensation, and other sources of contamination. The hard disk's read-write heads fly on an air bearing (a cushion of air) only nanometres above the disk surface. The disk surface and the drive's internal environment must therefore be kept immaculately clean, as fingerprints, hair, dust, and even smoke particles have mountain-sized dimensions when compared to the submicroscopic gap that the heads maintain. Some people believe a disk drive contains a vacuum — this is incorrect, as the system relies on air pressure inside the drive to support the heads at their proper ''flying height'' while the disk is in motion. Another common misconception is that a hard drive is totally sealed. A hard disk drive requires a certain range of air pressures in order to operate properly. If the air pressure is too low, the air will not exert enough force on the flying head, the head will not be at the proper height, and there is a risk of head crashes and data loss. (Specially manufactured sealed and pressurized drives are needed for reliable high-altitude operation, above about 10,000 feet. Please note this does not apply to pressurized enclosures, like an aircraft cabin.) Modern drives include temperature sensors and adjust their operation to the operating environment. Hard disk drives are not airtight. They have a permeable filter (a breather filter) between the top cover and inside of the drive, to allow the pressure inside and outside the drive to equalize while keeping out dust and dirt. The filter also allows moisture in the air to enter the drive. Very high humidity year-round will cause accelerated wear of the drive's heads (by increasing stiction, or the tendency for the heads to stick to the disk surface, which causes physical damage to the disk and spindle motor). You can see these breather holes on all drives -- they usually have a warning sticker next to them, informing the user not to cover the holes. The air inside the operating drive is constantly moving too, being swept in motion by friction with the spinning disk platters. This air passes through an internal filter to remove any leftover contaminants from manufacture, any particles that may have somehow entered the drive, and any particles generated by head crash. Due to the extremely close spacing of the heads and disk surface, any contamination of the read-write heads or disk platters can lead to a head crash — a failure of the disk in which the head scrapes across the platter surface, often grinding away the thin magnetic film. For Giant_magnetoresistive_effect heads in particular, a minor head crash from contamination (that does not remove the magnetic surface of the disk) will still result in the head temporarily overheating, due to friction with the disk surface, and renders the disk unreadable until the head temperature stabilizes. Head crashes can be caused by electronic failure, a sudden power failure, physical shock, wear and tear, or poorly manufactured disks. Normally, when powering down, a hard disk moves its heads to a safe area of the disk, where no data is ever kept (the ''landing zone''). However, especially in old models, sudden power interruptions or a power supply failure can result in the drive shutting down with the heads in the data zone, which increases the risk of data loss. Newer drives are designed such that the rotational inertia in the platters is used to safely park the heads in the case of unexpected power loss. In recent years, IBM pioneered drives with "head unloading" technology, where the heads are lifted off the platters onto "ramps" instead of having them rest on the platters, reducing the risk of stiction. Other manufacturers have begun using this technology as well. Spring tension from the head mounting constantly pushes the heads towards the disk. While the disk is spinning, the heads are supported by an air bearing, and experience no physical contact wear. The sliders (the part of the head that is closest to the disk and contains the pickup coil itself) are designed to reliably survive a number of landings and takeoffs from the disk surface, though wear and tear on these microscopic components eventually takes its toll. Most manufacturers design the sliders to survive 50,000 contact cycles before the chance of damage on startup rises above 50%. However, the decay rate is not linear — when a drive is younger and has fewer start/stop cycles, it has a better chance of surviving the next startup than an older, higher-mileage drive (literally, as the head drags along the drive surface until the air bearing is established). The Maxtor DiamondMax series of desktop hard drives, for instance are rated to 50,000 start-stop cycles. This means that during testing no failures contributed to the head-disk interface are seen before at least 50,000 start-stop cycles. Using rigid platters and sealing the unit allows much tighter tolerances than in a floppy disk. Consequently, hard disks can store much more data than floppy disk, and access and transmit it faster. In 2005, a typical workstation hard disk might store between 80 GB and 400 GB of data, rotate at 7,200 to 10,000 rpm, and have a sequential transfer rate of over 50 MB/s. The fastest workstation hard drives spin at 15,000 rpm. Notebook hard drives, which are physically smaller than their desktop counterparts, tend to be slower and have less capacity. Most spin at only 4,200 rpm or 5,400 rpm, though the newest top models spin at 7,200 rpm. ==Performance== There are three primary factors that determine hard drive performance: seek time, rotational delay and internal data transfer rate: * Seek time is a measure of the speed with which the drive can position its read/write heads over any particular data track. Because neither the starting position of the head nor the distance from there to the desired track is fixed, seek time varies greatly, and it is almost always measured as an ''average seek time'', though ''full-track'' (the longest possible) and ''track-to-track'' (the shortest possible) seeks are also quoted sometimes. The standard way to measure seek time is to time a large number of disk accesses to random locations, subtract the latency (see below) and take the mean. Note, however, that two different drives with identical average seek times can display quite different performance characteristics. Seek time is always measured in milliseconds (ms), and often regarded as the single most important determinant of drive performance, though this claim is debated. (More on seek time.) * All drives have rotational latency: the time that elapses between the moment when the read/write head settles over the desired data track and the moment when the first byte of the required data appears under the head. For any individual read or write operation, latency is random between zero (if the first data sector happens to be directly under the head at the exact moment that the head is ready to begin reading or writing) and the full rotational period of the drive (for a typical 7200 rpm drive, just under 8.4 ms). However, on average, latency is ''always'' equal to one half of the rotational period. Thus, all 5400 rpm drives of any make or model have 5.56 ms latency; all 7200 rpm drives, 4.17 ms; all 10,000 rpm drives, 3.0 ms; and all 15,000 rpm drives have 2.0 ms latency. Like seek time, latency is a critical performance factor and is always measured in milliseconds. (More on rotational delay.) * The internal data rate is the speed with which the drive's internal read channel can transfer data from the magnetic media. (Or, less commonly, in the reverse direction.) Previously a very important factor in drive performance, it remains significant but less so than in prior years, as all modern drives have very high internal data rates. Internal data rates are normally measured in Mega''bits'' per second (Bits per second). Subsidiary performance factors include: * Access time is simply the sum of the seek time and the latency. It is important not to mistake seek time figures for access time figures! The access time is by far the most important performance benchmark of a modern HDD. It almost alone defines how fast the disk performs in a typical system. However, people tend to pay much more attention to the data rates, which rarely make any significant difference in typical systems. Of course, in some usage scenarios it may be vise-versa, so you need to know your system before buying a HDD. * The external data rate is the speed with which the drive can transfer data from its buffer to the host computer system. Although in theory this is vital, in practice it is usually a non-issue. It is a relatively trivial matter to design an electronic interface capable of outpacing any possible mechanical read/write mechanism, and it is routine for computer makers to include a hard drive controller interface that is significantly faster than the drive it will be attached to. As a general rule, modern Advanced Technology Attachment and SCSI interfaces are capable of dealing with at least twice as much data as any single drive can deliver; they are, after all, designed to handle two or more drives per bus even though a desktop computer usually mounts only one. For a single-drive computer, the difference between ATA-100 and ATA-133, for example, is largely one of marketing rather than performance. No drive yet manufactured can utilise the full bandwidth of an ATA-100 interface, and few are able to send more data than an ATA-66 interface can accept. The external data rate is usually measured in MB/second or Mebibyte/second. * Command overhead is the time it takes the drive electronics to interpret instructions from the host computer and issue commands to the read/write mechanism. In modern drives it is negligible. ==Access and interfaces== A hard disk is generally accessed over one of a number of bus types, including Advanced_Technology_Attachment (IDE, EIDE), SCSI, FireWire/IEEE 1394, Universal Serial Bus, and Fibre Channel. In late 2002 Serial ATA was introduced. Back in the days of the ST-506 interface, the data encoding scheme was also important. The first ST-506 disks used Modified Frequency Modulation (MFM) encoding (which is still used on the common "1.44 MB" (1.4 Mebibyte) 3.5-inch floppy), and ran at a data rate of 5 megabits per second. Later on, controllers using ''2,7 RLL'' (or just "RLL") encoding increased this by half, to 7.5 megabits per second; it also increased drive capacity by half. Many ST-506 interface drives were only certified by the manufacturer to run at the lower MFM data rate, while other models (usually more expensive versions of the same basic drive) were certified to run at the higher RLL data rate. In some cases, the drive was overengineered just enough to allow the MFM-certified model to run at the faster data rate; however, this was often unreliable and was not recommended. (An RLL-certified drive could run on a MFM controller, but with 1/3 less data capacity and speed.) ESDI also supported multiple data rates (ESDI drives always used 2,7 RLL, but at 10, 15 or 20 megabits per second), but this was usually negotiated automatically by the drive and controller; most of the time, however, 15 or 20 megabit ESDI drives weren't downward compatible (i.e. a 15 or 20 megabit drive wouldn't run on a 10 megabit controller). ESDI drives typically also had jumpers to set the number of sectors per track and (in some cases) sector size. SCSI originally had just one speed, 5 MHz (for a maximum data rate of 5 megabytes per second), but this was increased dramatically later. The SCSI bus speed had no bearing on the drive's internal speed because of buffering between the SCSI bus and the drive's internal data bus; however, many early drives had very small buffers, and thus had to be reformatted to a different interleave (just like ST-506 drives) when used on slow computers, such as early IBM PC compatibles and Apple Macintoshes. ATA drives have typically had no problems with interleave or data rate, due to their controller design, but many early models were incompatible with each other and couldn't run in a master/slave setup (two drives on the same cable). This was mostly remedied by the mid-1990s, when ATA's specfication was standardised and the details begun to be cleaned up, but still causes problems occasionally (especially with CD-ROM and DVD-ROM drives, and when mixing Ultra DMA and non-UDMA devices). Serial ATA does away with master/slave setups entirely, placing each drive on its own channel (with its own set of I/O ports) instead. FireWire/IEEE 1394 and USB(1.0/2.0) hard disks are external units containing generally ATA or SCSI drives with ports on the back allowing very simple and effective expansion and mobility. Most FireWire/IEEE 1394 models are able to Daisy chain#Computer Engineering in order to continue adding peripherals without requiring additional ports on the computer itself. == Other characteristics == * Capacity (measured in gigabytes) * MTBF (mean time between failures) * Power consumption (especially important in battery-powered laptops) * audible noise (in dBA) * G-shock rating (surprisingly high in modern drives) ==Addressing modes== There are two modes of addressing the data blocks on more recent hard disks. The older one is the CHS addressing (Cylinder-Head-Sector), used on old ST-506 and ATA drives and internally by the PC BIOS, and the more recent one the LBA (Logical block addressing), used by SCSI drives and newer ATA drives (ATA drives power up in CHS mode for historical reasons). CHS describes the disk space in terms of its physical dimensions, data-wise; this is the traditional way of accessing a disk on IBM PC compatible hardware, and while it works well for floppies (for which it was originally designed) and small hard disks, it caused problems when disks started to exceed the design limits of the PC's CHS implementation. The traditional CHS limit was 1024 cylinders, 16 heads and 63 sectors; on a drive with 512-byte sectors, this comes to 504 MiB (528 megabytes). The origin of the CHS limit lies in a combination of the limitations of IBM's BIOS interface (which allowed 1024 cylinders, 256 heads and 64 sectors; sectors were counted from 1, reducing that number to 63, giving an addressing limit of 8064 MiB or 7.8 Gibibyte), and a hardware limitation of the AT's hard disk controller (which allowed up to 65536 cylinders and 256 sectors, but only 16 heads, putting its addressing limit at 2^28 bits or 128 GiB). When drives larger than 504 MiB began to appear in the mid-1990s, many system BIOSes had problems communicating with them, requiring LBA BIOS upgrades or special driver software to work correctly. Even after the introduction of LBA, similar limitations reappeared several times over the following years: at 2.1, 4.2, 8.4, 32, and 128 GiB. The 2.1, 4.2 and 32 GiB limits are ''hard limits'': fitting a drive larger than the limit results in a PC that refuses to boot, unless the drive includes special jumpers to make it appear as a smaller capacity. The 8.4 and 128 GiB limits are ''soft limits'': the PC simply ignores the extra capacity and reports a drive of the maximum size it is able to communicate with. SCSI drives, however, have always used LBA addressing, which describes the disk as a linear, sequentially-numbered set of blocks. SCSI mode page commands can be used to get the physical specifications of the disk, but this is not used to read or write data; this is an artifact of the early days of SCSI, circa 1986, when a disk attached to a SCSI bus could just as well be an ST-506 or ESDI drive attached through a bridge (and therefore having a CHS configuration that was subject to change) as it could a native SCSI device. Because PCs use CHS addressing internally, the BIOS code on PC SCSI host adapters does CHS-to-LBA translation, and provides a set of CHS drive parameters that tries to match the total number of LBA blocks as closely as possible. ATA drives can either use their native CHS parameters (only on very early drives; hard drives made since the early 1990s use zone bit recording, and thus don't have a set number of sectors per track), use a "translated" CHS profile (similar to what SCSI host adapters provide), or run in ATA LBA mode, as specified by ATA-2. To maintain some degree of compatibility with older computers, LBA mode generally has to be requested explicitly by the host computer. ATA drives larger than 8 GiB are always accessed by LBA, due to the 8 GiB limit described above. See also: hard disk drive partitioning, master boot record, file system, drive letter assignment, boot sector. ==Manufacturers== [[image:Hitachinotebookhd.jpg|thumb|right|250px|Hitachi 2.5 inch laptop hard drive]] Most of the world's hard disks are now manufactured by just a handful of large firms: Seagate, Maxtor Corporation, Western Digital, Samsung, and the former drive manufacturing division of International Business Machines, now sold to Hitachi (company). Fujitsu continues to make specialist notebook and SCSI drives but exited the mass market in 2001. Toshiba is a major manufacturer of 2.5-inch and 1.8-inch notebook drives. ===Firms that have come and gone=== Dozens of former hard drive manufacturers have gone out of business, merged, or closed their hard drive divisions; as capacities and demand for products increased, profits became hard to find, and there were shakeouts in the late 1980s and late 1990s. The first notable casualty of the business in the PC era was Computer Memories International or CMI; after the 1985 incident with the faulty 20MB AT drives, CMI's reputation never recovered, and they exited the hard drive business in 1987. Another notable failure was MiniScribe, who went bankrupt in 1990 after it was found that they had "cooked the books" and inflated sales numbers for several years. Many other smaller companies (like Kalok, Microscience International Corporation, LaPine, Areal, Priam and PrairieTek) also did not survive the shakeout, and had disappeared by 1993; Micropolis Corporation was able to hold on until 1997, and JT Storage, a relative latecomer to the scene, lasted only a few years and was gone by 1999. Rodime plc was also an important manufacturer during the 1980s, but stopped making drives in the early 1990s amid the shakeout and now concentrates on technology licensing; they hold a number of patents related to 3.5-inch form factor hard drives. There have also been a number of notable mergers in the hard disk industry: *Tandon sold its disk manufacturing division to Western Digital (which was then a controller maker and Application-specific integrated circuit house) in 1988; by the early 1990s Western Digital disks were among the top sellers. *Quantum Corporation bought Digital Equipment Corporation's storage division in 1994, and later (2000) sold the hard disk division to Maxtor to concentrate on tape drives. *In 1995, Conner Peripherals announced a merger with Seagate (who had earlier bought Imprimis from Control Data Corporation), which completed in early 1996. *JTS infamously merged with Atari in 1996, giving it the capital it needed to bring its drive range into production. *In 2003, following the controversy over the mass failures of the Deskstar 75GXP range (which resulted in lost sales of its follow-ons), hard disk pioneer IBM sold the majority of its disk division to Hitachi, who renamed it ''Hitachi Global Storage Technologies''. ==="Marketing" capacity versus true capacity=== It is important to note that hard drive manufacturers often use the SI_prefix definition of the prefixes "giga" and "mega." However, nearly all operating system utilities report capacities using binary definitions for the prefixes. This is largely historical, since when storage capacities started to exceed thousands of bytes, there were no standard binary prefixes (the IEC only standardized Binary_prefix#IEC_standard_prefixes in 1999), so 210 (1024) bytes was called a kilobyte because 1024 is "close enough" to the metric prefix kilo, which is defined as 103 or 1000. This trend became habit and continued to be applied to the prefixes "mega," "giga," and even "tera." Obviously the discrepancy becomes much more noticeable in reported capacities in the multiple gigabyte range, and users will often notice that the volume capacity reported by their OS is significantly less than that advertised by the hard drive manufacturer. For example, a drive advertised as 200 GB can be expected to store close to 200 x 109, or 200 billion, bytes. This uses the proper SI definition of "giga," 109 and cannot be considered as incorrect. Since utilities provided by the operating system probably define a Gigabyte as 230, or 1073741824, bytes, the reported capacity of the drive will be closer to 186.26 GB (actually, GiB), a difference of well over ten gigabytes. For this very reason, many utilities that report capacity have begun to use the aforementioned IEC standard binary prefixes (e.g. KiB, MiB, GiB) since their definitions are not ambiguous. Another side point is that many people mistakenly attribute the discrepancy in reported and advertised capacities to reserved space used for file system and partition accounting information. However, for large (several GiB) filesystems, this data rarely occupies more than several MiB, and therefore cannot possibly account for the apparent "loss" of tens of Gigabytes. ==Hard disk usage== From the original use of a hard drive in a single computer, techniques for guarding against hard disk failure were developed such as the redundant array of independent disks (RAID). Hard disks are also found in network attached storage (NAS) devices, but for large volumes of data are most efficiently used in a storage area network (SAN). Applications for hard disk drives expanded to include personal video recorders, digital audio players, Personal digital assistant and digital cameras. In 2005 the first cellular telephones to include hard disk drives were introduced by Samsung_Group and Nokia. ==History== The first computer with a hard disk drive as standard was the IBM 350 Disk File, introduced in 1955 with the IBM 305 computer. This drive had fifty 24 inch platters, with a total capacity of five million characters. In 1952, an IBM engineer named Reynold Johnson developed a massive hard disk consisting of fifty platters, each two feet wide, that rotated on a spindle at 1200 rpm with read/write heads for the first database running RCAs Bismark computer. In 1973, IBM introduced the IBM 3340 "Winchester" disk system (the 30MB + 30 millisecond access time led the project to be named after the Winchester rifle), the first to use a sealed head/disk assembly (HDA). Almost all modern disk drives now use this technology, and the term "Winchester" became a common description for all hard disks, though generally falling out of use during the 1990s. For many years, hard disks were large, cumbersome devices, more suited to use in the protected environment of a data center or large office than in a harsh industrial environment (due to their delicacy), or small office or home (due to their size and power consumption). Before the early 1980s, most hard disks had 8-inch or 14-inch platters, required an equipment rack or a large amount of floor space (especially the large removable-media drives, which were often referred to as "washing machines"), and in many cases needed special power hookups for the large motors they used. Because of this, hard disks were not commonly used with microcomputers until after 1980, when Seagate Technology introduced the ST-506, the first 5.25-inch hard drive, with a capacity of 5 megabytes. In fact, in its factory configuration the original IBM PC (IBM 5150) was not equipped with a hard drive. Most microcomputer hard disk drives in the early 1980s were not sold under their manufacturer's names, but by Original equipment manufacturers as part of larger peripherals (such as the Corvus Disk System and the Apple ProFile). The IBM PC/XT had an internal hard disk, however, and this started a trend toward buying "bare" drives (often by mail order) and installing them directly into a system. Hard disk makers started marketing to end users as well as OEMs, and by the mid-1990s, hard disks had become available on retail store shelves. While internal drives became the system of choice on PCs, external hard drives remained popular for much longer on the Apple Macintosh and other platforms. Every Mac made between 1986 and 1998 has a SCSI port on the back, making external expansion easy; also, "toaster" Macs did not have easily accessible hard drive bays (or, in the case of the Mac Plus, any hard drive bay at all), so on those models, external SCSI disks were the only reasonable option. External SCSI drives were also popular with older microcomputers such as the Apple II series and the Commodore 64, and were also used extensively in servers, a usage which is still popular today. The appearance in the late 1990s of high-speed external interfaces such as Universal Serial Bus and IEEE 1394 (FireWire) has made external disk systems popular among regular users once again, especially for users that move large amounts of data between two or more locations, and most hard disk makers now make their disks available in external cases. The capacity of hard drives has grown exponentially over time. With early personal computers, a drive with a 20 megabyte capacity was considered large. In the latter half of the 1990's, hard drives with capacities of 1 gigabyte and greater became available. As of early 2005, the "smallest" desktop hard disk in production has a capacity of 40 gigabytes, while the largest-capacity internal drives are a half terabyte (500 gigabytes), with external drives at or exceeding one terabyte. As far as PC history is concerned, the major drive families have been Modified Frequency Modulation, Run Length Limited, Enhanced Small Disk Interface, SCSI, Advanced Technology Attachment, and now Serial ATA. MFM drives required that the electronics on the "controller" be compatible with the electronics on the card - disks and controllers had to be compatible. RLL (Run Length Limited) was a way of encoding bits onto the platters that allowed for better density. Most RLL drives also needed to be "compatible" with the controllers that communicated with them. ESDI was an interface developed by Maxtor. It allowed for faster comminication between the PC and the disk. SCSI (originally named SASI for Shugart (sic) Associates) or Small Computer System Interface was an early competitor with ESDI. When the price of electronics dropped (and because of a demand by consumers) the electronics that had been stored on the controller card was moved to the disk drive itself. This advance was known as "Independent Drive Electronics" or IDE. Eventually, IDE manufacturers wanted the speed of IDE to approach the speed of SCSI drives. IDE drives were slower because they did not have as big a cache as the SCSI drives, and they could not write directly to RAM. IDE manufacturers attempted to close this speed gap by introducing Logical Block Addressing (LBA). These drives were known as EIDE. While EIDE was introduced, though, SCSI manufacturers continued to improve SCSI's performance. The increase in SCSI performance came at a price -its interfaces were more expensive. In order for EIDE's performance to increase (while keeping the cost of the associated electronics low), it was realized that the only way to do this was to move from "parallel" interfaces to "serial" interfaces, the result of which is the SATA interface. However, as for 2005, performance of SATA and PATA disks is comparable. Fiber channel interfaces are left to discussions of server drives. ==See also== *Early IBM disk storage *Superparamagnetic effect ==External links== * The PC Guide: [http://www.pcguide.com/ref/hdd/hist-c.html A Brief History of the Hard Disk Drive] *[http://www.pcguide.com/intro/fun/bindec.htm Binary versus Decimal] *[http://www.nyx.net/~sgjoen/disk.html Multi Disk System Tuning HOWTO] *[http://www.microsoft.com/technet/archive/winntas/support/diskover.mspx Windows NT Server Resource Kit: Disk Management Basics] (See section "About Disks and Disk Organization") *[http://www.legadoassociates.com/behold.htm Behold the God Box] - Less's Law and future implications of massive cheap hard disk storage *[http://www.geekzone.co.nz/content.asp?contentid=4319 Hitachi's plans for perpendicular recording allowing 20 GB microdrives or 1 TB 3.5 inch drives] *[http://www.hitachigst.com/hdd/research/recording_head/pr/PerpendicularAnimation.html Get Perpendicular] Computer storage devices Rotating disc computer storage media Computing Computer storage media ms:Cakera keras nds:Fastplaat th:ฮาร์ดดิสก์
==IEC Binary Prefixes== My feeling is that all the storage capacity units in this article should be changed to the Binary_prefix#IEC_standard_prefixes for clarity. The only objection I can see to this is that the traditional usage of the metric prefixes is more widely recognized. However, I feel this is trivial since the binary abbreviations (i.e. KiB, MiB, GiB, as opposed to KB, MB, GB, respectively) are very similar to their metric counterparts, the difference will not be noticed by most readers, but it does a lot in the way of accuracy for this somewhat confusing matter. In any case, the current state of the article is inconstistant in its use of IEC binary and metric prefixes, and something should be done either way. Please post your comments either supporting or objecting to this, I didn't want to make this kind of an edit without first consulting some others. -- User:Uberpenguin 18:10, 2005 Mar 28 (UTC) ---- Hmm, would anyone be willing to create and/or add a schematic of the interior of a hard drive? I was wondering what typical random access times might be for various types of drives. I just ran a benchmark program on my HD and I was wondering how it compared to others. KM Typical current mass-market drives have ''seek'' times of around 9ms. Add just over 4ms latency to that (for a 7200 RPM drive) and you have an average access time of about 13.5ms. A seriously high-perforance drive has a seek time of under 4ms and latency of 2ms - i.e., 6ms average access. But these drives sacrifice capacity to achieve their very high performance, require a SCSI interface, and are fairly expensive. User:Tannin Tannin, any particular reason for reverting my change to an auto-generated thumbnail? There's really no reason to have separate thumbnail images anymore, and that particular image has already been listed on WP:VFD after being replaced at Computer storage. User:DopefishJustin 03:44, Apr 26, 2004 (UTC) Yes Justin. It looks terrible, and defaces a perfectly good photograph. If you want to fuzz-up an image, do it to one you took yourself. User:Tannin Mr Anon, please note that a ''hard disk'' is the ''internal part'' of a hard disk drive. The terms are not synonyms. ==MFM History== I have no idea why the article claimed that MFM was invented for floppy drives. As far as I've been able to determine, MFM was first used on the IBM 3330 in 1971. The 3330 was most certainly NOT a floppy drive. The first use of MFM for a floppy drive appears to have been the IBM 53FD drive, introduced in 1977. --User:Brouhaha 08:04, 3 Sep 2004 (UTC) == damage == There's nothing written about the damage to hard disks: we should have at least a cursory explanation of the terms MTBF (mean time before failure), bad sectors/blocks/clusters, BBR (bad block relocation), handling by software and by hardware, hot swapping, something about refurbishing... --User:Joy 14:29, 27 Sep 2004 (UTC) == == "Disk Drive Speeds and Performance" http://www.notebookreview.com/forums/topic.asp?TOPIC_ID=112 == Decimal vs Binary == It seems like the following claim is incorrect. “It is important to note that hard drive manufacturers often use the decimal definition of a gigabyte or megabyte. As a result, after the drive is installed it appears that a few gigabytes or megabytes have disappeared. In reality computers operate based upon the binary numeral system. In the decimal number system a gigabyte is 7.5% smaller than in the binary number system. The term "1.44 MB", often used to describe 1440 KB floppies (actually 1.47 MB or 1.4 MiB), introduced an anomalous definition of "megabyte" as 1 × 103 × 210 bytes (1 KKiB).” The manufacturers actually state a smaller raw capacity of their drives. That is a 30GB harddrive is actually 30GB X 1.024. The reason that the actual HD is smaller than the advertised number is because some bits are reserved for sector information and thing of the like depending on the OS that’s used. This is my take on thing. Please let me know what you think, so that we can update this article if required. :No, the text in the article is correct, if a bit innaccurate on a technicality. The issue here is actually the binary PREFIX versus the metric prefix. This is largely historical; when this first became an issue there were no binary prefixes, so 2^10 bytes was called a kilobyte since 1024 (2^10) is close enough to 1000 (10^3). However, the problem becomes more noticible when you get into the multiple gigabyte range. Most OSes report a GB as what is now called a GiB, or Gibibyte; 2^30 bytes. Hard drive manufacturers continue to use the metric definition of a GB: 10^9, which is obviously less than the binary Gibibyte, because it makes it seem like the drive has a higher capacity than it actually does. :The blocks used for partition and file system accounting information rarely occupy more than a few KiB, and is utterly insignificant when talking about discrepencies of tens of Gibibytes. I'll edit this section of the article to be a little more clear. -- User:Uberpenguin 15:16, 2005 Apr 4 (UTC) == perpendicular recording == Does anybody have a more detailed description of what perpendicular recording is? I checked over at Valdemar Poulsen page and i couldn't find anything about his discovery as this paragraph from the linked article asserts. "Perpendicular recording was pioneered by the late 19th century work of Danish scientist Valdemar Poulsen, who demonstrated magnetic recording with his telegraphone." [http://news.bbc.co.uk/2/hi/technology/4411649.stm] == Altitude Sensor? == "Some modern drives include flying height sensors to detect if the pressure is too low, and temperature sensors to alert the system to overheating problems." I do not believe that as of today, April 2005, there are any hard drives that have an altitude sensor as these are still to costly. Every modern drive has a temperature sensor. Channel parameters are typically adapted to the measured temperature. User:BruceSchardt == Start Stop CSS Testing == I changed the discussion of startstop or CSS testing because the statement that 50% of the drives fail at 50,000 cycles is not correct. Typical specification for a desktop harddrive is 50,000 cycles. However this is not a mean time (cycles) till failure specification. This is a specification that all drives are supposed to achieve without failure. In typical testing a population of several hundred drives are contact-start-stop (CSS) tested for >100,000 cycles. No failures caused by the head-disk interface are allowed at less then 50,000 cycles. Testing for more then 50,000 cycles insures that the HDI design has margin. In proof, the Maxtor Diamondmax 10 hardrive specifies Start-Stop cycles at >50,000 min.[http://www.maxtor.com/_files/maxtor/en_us/documentation/data_sheets/diamondmax_10_data_sheet.pdf] Notebook hard drives are all load-unload designs that never park the heads on the disk, instead the heads are unloaded onto a ramp. This is done to increase the magnitude of non-operational shock that the drive can withstand. User:BruceSchardt
See other meanings of words starting from letter:
Words begining with Hard_disk:
Hard-disk
Hard-disk_recording
Hard_Disk
Hard_disk
Hard_disk
Hard_disks
Hard_disk_controller
Hard_disk_drive
Hard_disk_drives
Hard_disk_drive_functioning
Hard_disk_drive_partition
Hard_disk_drive_partitioning
Hard_disk_drive_partitioning
Hard_disk_platter
Hard_disk_platter
Hard_disk_recorder
Hard_disk_recording
Hard Disk
#REDIRECT Hard disk
Hard disk
A hard disk (or "hard disc" or "hard drive" or "hard disk drive") is a computer data storage device that stores data on rotating magnetic surfaces. ==Mechanics== A hard disk uses rigid rotating hard disk platter (disks). It stores and retrieves digital data from a planar magnetic surface. Information is written to the disk by transmitting an electromagnetic flux through an antenna or ''write head'' that is very close to a magnetic material, which in turn changes its polarization due to the flux. The information can be read back in a reverse manner, as the magnetic fields cause electrical change in the coil or ''read head'' that passes over it. A typical hard disk drive design consists of a central axis or spindle upon which the platters spin at a constant speed. Moving along and between the platters on a common armature are the disk read-and-write head, with one head for each platter face. The armature moves the heads radially across the platters as they spin, allowing each head access to the entirety of the platter. The associated electronics control the movement of the read-write armature and the rotation of the disk, and perform reads and writes on demand from the disk controller. Modern drive electronics are capable of scheduling reads and writes efficiently across the disk, and of remapping sectors of the disk which have failed. Also, most major hard drive and motherboard vendors now support Self-Monitoring, Analysis and Reporting Technology technology, by which impending failures can often be predicted, allowing the user to be alerted in time to prevent data loss. The (mostly) sealed enclosure protects the drive internals from dust, condensation, and other sources of contamination. The hard disk's read-write heads fly on an air bearing (a cushion of air) only nanometres above the disk surface. The disk surface and the drive's internal environment must therefore be kept immaculately clean, as fingerprints, hair, dust, and even smoke particles have mountain-sized dimensions when compared to the submicroscopic gap that the heads maintain. Some people believe a disk drive contains a vacuum — this is incorrect, as the system relies on air pressure inside the drive to support the heads at their proper ''flying height'' while the disk is in motion. Another common misconception is that a hard drive is totally sealed. A hard disk drive requires a certain range of air pressures in order to operate properly. If the air pressure is too low, the air will not exert enough force on the flying head, the head will not be at the proper height, and there is a risk of head crashes and data loss. (Specially manufactured sealed and pressurized drives are needed for reliable high-altitude operation, above about 10,000 feet. Please note this does not apply to pressurized enclosures, like an aircraft cabin.) Modern drives include temperature sensors and adjust their operation to the operating environment. Hard disk drives are not airtight. They have a permeable filter (a breather filter) between the top cover and inside of the drive, to allow the pressure inside and outside the drive to equalize while keeping out dust and dirt. The filter also allows moisture in the air to enter the drive. Very high humidity year-round will cause accelerated wear of the drive's heads (by increasing stiction, or the tendency for the heads to stick to the disk surface, which causes physical damage to the disk and spindle motor). You can see these breather holes on all drives -- they usually have a warning sticker next to them, informing the user not to cover the holes. The air inside the operating drive is constantly moving too, being swept in motion by friction with the spinning disk platters. This air passes through an internal filter to remove any leftover contaminants from manufacture, any particles that may have somehow entered the drive, and any particles generated by head crash. Due to the extremely close spacing of the heads and disk surface, any contamination of the read-write heads or disk platters can lead to a head crash — a failure of the disk in which the head scrapes across the platter surface, often grinding away the thin magnetic film. For Giant_magnetoresistive_effect heads in particular, a minor head crash from contamination (that does not remove the magnetic surface of the disk) will still result in the head temporarily overheating, due to friction with the disk surface, and renders the disk unreadable until the head temperature stabilizes. Head crashes can be caused by electronic failure, a sudden power failure, physical shock, wear and tear, or poorly manufactured disks. Normally, when powering down, a hard disk moves its heads to a safe area of the disk, where no data is ever kept (the ''landing zone''). However, especially in old models, sudden power interruptions or a power supply failure can result in the drive shutting down with the heads in the data zone, which increases the risk of data loss. Newer drives are designed such that the rotational inertia in the platters is used to safely park the heads in the case of unexpected power loss. In recent years, IBM pioneered drives with "head unloading" technology, where the heads are lifted off the platters onto "ramps" instead of having them rest on the platters, reducing the risk of stiction. Other manufacturers have begun using this technology as well. Spring tension from the head mounting constantly pushes the heads towards the disk. While the disk is spinning, the heads are supported by an air bearing, and experience no physical contact wear. The sliders (the part of the head that is closest to the disk and contains the pickup coil itself) are designed to reliably survive a number of landings and takeoffs from the disk surface, though wear and tear on these microscopic components eventually takes its toll. Most manufacturers design the sliders to survive 50,000 contact cycles before the chance of damage on startup rises above 50%. However, the decay rate is not linear — when a drive is younger and has fewer start/stop cycles, it has a better chance of surviving the next startup than an older, higher-mileage drive (literally, as the head drags along the drive surface until the air bearing is established). The Maxtor DiamondMax series of desktop hard drives, for instance are rated to 50,000 start-stop cycles. This means that during testing no failures contributed to the head-disk interface are seen before at least 50,000 start-stop cycles. Using rigid platters and sealing the unit allows much tighter tolerances than in a floppy disk. Consequently, hard disks can store much more data than floppy disk, and access and transmit it faster. In 2005, a typical workstation hard disk might store between 80 GB and 400 GB of data, rotate at 7,200 to 10,000 rpm, and have a sequential transfer rate of over 50 MB/s. The fastest workstation hard drives spin at 15,000 rpm. Notebook hard drives, which are physically smaller than their desktop counterparts, tend to be slower and have less capacity. Most spin at only 4,200 rpm or 5,400 rpm, though the newest top models spin at 7,200 rpm. ==Performance== There are three primary factors that determine hard drive performance: seek time, rotational delay and internal data transfer rate: * Seek time is a measure of the speed with which the drive can position its read/write heads over any particular data track. Because neither the starting position of the head nor the distance from there to the desired track is fixed, seek time varies greatly, and it is almost always measured as an ''average seek time'', though ''full-track'' (the longest possible) and ''track-to-track'' (the shortest possible) seeks are also quoted sometimes. The standard way to measure seek time is to time a large number of disk accesses to random locations, subtract the latency (see below) and take the mean. Note, however, that two different drives with identical average seek times can display quite different performance characteristics. Seek time is always measured in milliseconds (ms), and often regarded as the single most important determinant of drive performance, though this claim is debated. (More on seek time.) * All drives have rotational latency: the time that elapses between the moment when the read/write head settles over the desired data track and the moment when the first byte of the required data appears under the head. For any individual read or write operation, latency is random between zero (if the first data sector happens to be directly under the head at the exact moment that the head is ready to begin reading or writing) and the full rotational period of the drive (for a typical 7200 rpm drive, just under 8.4 ms). However, on average, latency is ''always'' equal to one half of the rotational period. Thus, all 5400 rpm drives of any make or model have 5.56 ms latency; all 7200 rpm drives, 4.17 ms; all 10,000 rpm drives, 3.0 ms; and all 15,000 rpm drives have 2.0 ms latency. Like seek time, latency is a critical performance factor and is always measured in milliseconds. (More on rotational delay.) * The internal data rate is the speed with which the drive's internal read channel can transfer data from the magnetic media. (Or, less commonly, in the reverse direction.) Previously a very important factor in drive performance, it remains significant but less so than in prior years, as all modern drives have very high internal data rates. Internal data rates are normally measured in Mega''bits'' per second (Bits per second). Subsidiary performance factors include: * Access time is simply the sum of the seek time and the latency. It is important not to mistake seek time figures for access time figures! The access time is by far the most important performance benchmark of a modern HDD. It almost alone defines how fast the disk performs in a typical system. However, people tend to pay much more attention to the data rates, which rarely make any significant difference in typical systems. Of course, in some usage scenarios it may be vise-versa, so you need to know your system before buying a HDD. * The external data rate is the speed with which the drive can transfer data from its buffer to the host computer system. Although in theory this is vital, in practice it is usually a non-issue. It is a relatively trivial matter to design an electronic interface capable of outpacing any possible mechanical read/write mechanism, and it is routine for computer makers to include a hard drive controller interface that is significantly faster than the drive it will be attached to. As a general rule, modern Advanced Technology Attachment and SCSI interfaces are capable of dealing with at least twice as much data as any single drive can deliver; they are, after all, designed to handle two or more drives per bus even though a desktop computer usually mounts only one. For a single-drive computer, the difference between ATA-100 and ATA-133, for example, is largely one of marketing rather than performance. No drive yet manufactured can utilise the full bandwidth of an ATA-100 interface, and few are able to send more data than an ATA-66 interface can accept. The external data rate is usually measured in MB/second or Mebibyte/second. * Command overhead is the time it takes the drive electronics to interpret instructions from the host computer and issue commands to the read/write mechanism. In modern drives it is negligible. ==Access and interfaces== A hard disk is generally accessed over one of a number of bus types, including Advanced_Technology_Attachment (IDE, EIDE), SCSI, FireWire/IEEE 1394, Universal Serial Bus, and Fibre Channel. In late 2002 Serial ATA was introduced. Back in the days of the ST-506 interface, the data encoding scheme was also important. The first ST-506 disks used Modified Frequency Modulation (MFM) encoding (which is still used on the common "1.44 MB" (1.4 Mebibyte) 3.5-inch floppy), and ran at a data rate of 5 megabits per second. Later on, controllers using ''2,7 RLL'' (or just "RLL") encoding increased this by half, to 7.5 megabits per second; it also increased drive capacity by half. Many ST-506 interface drives were only certified by the manufacturer to run at the lower MFM data rate, while other models (usually more expensive versions of the same basic drive) were certified to run at the higher RLL data rate. In some cases, the drive was overengineered just enough to allow the MFM-certified model to run at the faster data rate; however, this was often unreliable and was not recommended. (An RLL-certified drive could run on a MFM controller, but with 1/3 less data capacity and speed.) ESDI also supported multiple data rates (ESDI drives always used 2,7 RLL, but at 10, 15 or 20 megabits per second), but this was usually negotiated automatically by the drive and controller; most of the time, however, 15 or 20 megabit ESDI drives weren't downward compatible (i.e. a 15 or 20 megabit drive wouldn't run on a 10 megabit controller). ESDI drives typically also had jumpers to set the number of sectors per track and (in some cases) sector size. SCSI originally had just one speed, 5 MHz (for a maximum data rate of 5 megabytes per second), but this was increased dramatically later. The SCSI bus speed had no bearing on the drive's internal speed because of buffering between the SCSI bus and the drive's internal data bus; however, many early drives had very small buffers, and thus had to be reformatted to a different interleave (just like ST-506 drives) when used on slow computers, such as early IBM PC compatibles and Apple Macintoshes. ATA drives have typically had no problems with interleave or data rate, due to their controller design, but many early models were incompatible with each other and couldn't run in a master/slave setup (two drives on the same cable). This was mostly remedied by the mid-1990s, when ATA's specfication was standardised and the details begun to be cleaned up, but still causes problems occasionally (especially with CD-ROM and DVD-ROM drives, and when mixing Ultra DMA and non-UDMA devices). Serial ATA does away with master/slave setups entirely, placing each drive on its own channel (with its own set of I/O ports) instead. FireWire/IEEE 1394 and USB(1.0/2.0) hard disks are external units containing generally ATA or SCSI drives with ports on the back allowing very simple and effective expansion and mobility. Most FireWire/IEEE 1394 models are able to Daisy chain#Computer Engineering in order to continue adding peripherals without requiring additional ports on the computer itself. == Other characteristics == * Capacity (measured in gigabytes) * MTBF (mean time between failures) * Power consumption (especially important in battery-powered laptops) * audible noise (in dBA) * G-shock rating (surprisingly high in modern drives) ==Addressing modes== There are two modes of addressing the data blocks on more recent hard disks. The older one is the CHS addressing (Cylinder-Head-Sector), used on old ST-506 and ATA drives and internally by the PC BIOS, and the more recent one the LBA (Logical block addressing), used by SCSI drives and newer ATA drives (ATA drives power up in CHS mode for historical reasons). CHS describes the disk space in terms of its physical dimensions, data-wise; this is the traditional way of accessing a disk on IBM PC compatible hardware, and while it works well for floppies (for which it was originally designed) and small hard disks, it caused problems when disks started to exceed the design limits of the PC's CHS implementation. The traditional CHS limit was 1024 cylinders, 16 heads and 63 sectors; on a drive with 512-byte sectors, this comes to 504 MiB (528 megabytes). The origin of the CHS limit lies in a combination of the limitations of IBM's BIOS interface (which allowed 1024 cylinders, 256 heads and 64 sectors; sectors were counted from 1, reducing that number to 63, giving an addressing limit of 8064 MiB or 7.8 Gibibyte), and a hardware limitation of the AT's hard disk controller (which allowed up to 65536 cylinders and 256 sectors, but only 16 heads, putting its addressing limit at 2^28 bits or 128 GiB). When drives larger than 504 MiB began to appear in the mid-1990s, many system BIOSes had problems communicating with them, requiring LBA BIOS upgrades or special driver software to work correctly. Even after the introduction of LBA, similar limitations reappeared several times over the following years: at 2.1, 4.2, 8.4, 32, and 128 GiB. The 2.1, 4.2 and 32 GiB limits are ''hard limits'': fitting a drive larger than the limit results in a PC that refuses to boot, unless the drive includes special jumpers to make it appear as a smaller capacity. The 8.4 and 128 GiB limits are ''soft limits'': the PC simply ignores the extra capacity and reports a drive of the maximum size it is able to communicate with. SCSI drives, however, have always used LBA addressing, which describes the disk as a linear, sequentially-numbered set of blocks. SCSI mode page commands can be used to get the physical specifications of the disk, but this is not used to read or write data; this is an artifact of the early days of SCSI, circa 1986, when a disk attached to a SCSI bus could just as well be an ST-506 or ESDI drive attached through a bridge (and therefore having a CHS configuration that was subject to change) as it could a native SCSI device. Because PCs use CHS addressing internally, the BIOS code on PC SCSI host adapters does CHS-to-LBA translation, and provides a set of CHS drive parameters that tries to match the total number of LBA blocks as closely as possible. ATA drives can either use their native CHS parameters (only on very early drives; hard drives made since the early 1990s use zone bit recording, and thus don't have a set number of sectors per track), use a "translated" CHS profile (similar to what SCSI host adapters provide), or run in ATA LBA mode, as specified by ATA-2. To maintain some degree of compatibility with older computers, LBA mode generally has to be requested explicitly by the host computer. ATA drives larger than 8 GiB are always accessed by LBA, due to the 8 GiB limit described above. See also: hard disk drive partitioning, master boot record, file system, drive letter assignment, boot sector. ==Manufacturers== [[image:Hitachinotebookhd.jpg|thumb|right|250px|Hitachi 2.5 inch laptop hard drive]] Most of the world's hard disks are now manufactured by just a handful of large firms: Seagate, Maxtor Corporation, Western Digital, Samsung, and the former drive manufacturing division of International Business Machines, now sold to Hitachi (company). Fujitsu continues to make specialist notebook and SCSI drives but exited the mass market in 2001. Toshiba is a major manufacturer of 2.5-inch and 1.8-inch notebook drives. ===Firms that have come and gone=== Dozens of former hard drive manufacturers have gone out of business, merged, or closed their hard drive divisions; as capacities and demand for products increased, profits became hard to find, and there were shakeouts in the late 1980s and late 1990s. The first notable casualty of the business in the PC era was Computer Memories International or CMI; after the 1985 incident with the faulty 20MB AT drives, CMI's reputation never recovered, and they exited the hard drive business in 1987. Another notable failure was MiniScribe, who went bankrupt in 1990 after it was found that they had "cooked the books" and inflated sales numbers for several years. Many other smaller companies (like Kalok, Microscience International Corporation, LaPine, Areal, Priam and PrairieTek) also did not survive the shakeout, and had disappeared by 1993; Micropolis Corporation was able to hold on until 1997, and JT Storage, a relative latecomer to the scene, lasted only a few years and was gone by 1999. Rodime plc was also an important manufacturer during the 1980s, but stopped making drives in the early 1990s amid the shakeout and now concentrates on technology licensing; they hold a number of patents related to 3.5-inch form factor hard drives. There have also been a number of notable mergers in the hard disk industry: *Tandon sold its disk manufacturing division to Western Digital (which was then a controller maker and Application-specific integrated circuit house) in 1988; by the early 1990s Western Digital disks were among the top sellers. *Quantum Corporation bought Digital Equipment Corporation's storage division in 1994, and later (2000) sold the hard disk division to Maxtor to concentrate on tape drives. *In 1995, Conner Peripherals announced a merger with Seagate (who had earlier bought Imprimis from Control Data Corporation), which completed in early 1996. *JTS infamously merged with Atari in 1996, giving it the capital it needed to bring its drive range into production. *In 2003, following the controversy over the mass failures of the Deskstar 75GXP range (which resulted in lost sales of its follow-ons), hard disk pioneer IBM sold the majority of its disk division to Hitachi, who renamed it ''Hitachi Global Storage Technologies''. ==="Marketing" capacity versus true capacity=== It is important to note that hard drive manufacturers often use the SI_prefix definition of the prefixes "giga" and "mega." However, nearly all operating system utilities report capacities using binary definitions for the prefixes. This is largely historical, since when storage capacities started to exceed thousands of bytes, there were no standard binary prefixes (the IEC only standardized Binary_prefix#IEC_standard_prefixes in 1999), so 210 (1024) bytes was called a kilobyte because 1024 is "close enough" to the metric prefix kilo, which is defined as 103 or 1000. This trend became habit and continued to be applied to the prefixes "mega," "giga," and even "tera." Obviously the discrepancy becomes much more noticeable in reported capacities in the multiple gigabyte range, and users will often notice that the volume capacity reported by their OS is significantly less than that advertised by the hard drive manufacturer. For example, a drive advertised as 200 GB can be expected to store close to 200 x 109, or 200 billion, bytes. This uses the proper SI definition of "giga," 109 and cannot be considered as incorrect. Since utilities provided by the operating system probably define a Gigabyte as 230, or 1073741824, bytes, the reported capacity of the drive will be closer to 186.26 GB (actually, GiB), a difference of well over ten gigabytes. For this very reason, many utilities that report capacity have begun to use the aforementioned IEC standard binary prefixes (e.g. KiB, MiB, GiB) since their definitions are not ambiguous. Another side point is that many people mistakenly attribute the discrepancy in reported and advertised capacities to reserved space used for file system and partition accounting information. However, for large (several GiB) filesystems, this data rarely occupies more than several MiB, and therefore cannot possibly account for the apparent "loss" of tens of Gigabytes. ==Hard disk usage== From the original use of a hard drive in a single computer, techniques for guarding against hard disk failure were developed such as the redundant array of independent disks (RAID). Hard disks are also found in network attached storage (NAS) devices, but for large volumes of data are most efficiently used in a storage area network (SAN). Applications for hard disk drives expanded to include personal video recorders, digital audio players, Personal digital assistant and digital cameras. In 2005 the first cellular telephones to include hard disk drives were introduced by Samsung_Group and Nokia. ==History== The first computer with a hard disk drive as standard was the IBM 350 Disk File, introduced in 1955 with the IBM 305 computer. This drive had fifty 24 inch platters, with a total capacity of five million characters. In 1952, an IBM engineer named Reynold Johnson developed a massive hard disk consisting of fifty platters, each two feet wide, that rotated on a spindle at 1200 rpm with read/write heads for the first database running RCAs Bismark computer. In 1973, IBM introduced the IBM 3340 "Winchester" disk system (the 30MB + 30 millisecond access time led the project to be named after the Winchester rifle), the first to use a sealed head/disk assembly (HDA). Almost all modern disk drives now use this technology, and the term "Winchester" became a common description for all hard disks, though generally falling out of use during the 1990s. For many years, hard disks were large, cumbersome devices, more suited to use in the protected environment of a data center or large office than in a harsh industrial environment (due to their delicacy), or small office or home (due to their size and power consumption). Before the early 1980s, most hard disks had 8-inch or 14-inch platters, required an equipment rack or a large amount of floor space (especially the large removable-media drives, which were often referred to as "washing machines"), and in many cases needed special power hookups for the large motors they used. Because of this, hard disks were not commonly used with microcomputers until after 1980, when Seagate Technology introduced the ST-506, the first 5.25-inch hard drive, with a capacity of 5 megabytes. In fact, in its factory configuration the original IBM PC (IBM 5150) was not equipped with a hard drive. Most microcomputer hard disk drives in the early 1980s were not sold under their manufacturer's names, but by Original equipment manufacturers as part of larger peripherals (such as the Corvus Disk System and the Apple ProFile). The IBM PC/XT had an internal hard disk, however, and this started a trend toward buying "bare" drives (often by mail order) and installing them directly into a system. Hard disk makers started marketing to end users as well as OEMs, and by the mid-1990s, hard disks had become available on retail store shelves. While internal drives became the system of choice on PCs, external hard drives remained popular for much longer on the Apple Macintosh and other platforms. Every Mac made between 1986 and 1998 has a SCSI port on the back, making external expansion easy; also, "toaster" Macs did not have easily accessible hard drive bays (or, in the case of the Mac Plus, any hard drive bay at all), so on those models, external SCSI disks were the only reasonable option. External SCSI drives were also popular with older microcomputers such as the Apple II series and the Commodore 64, and were also used extensively in servers, a usage which is still popular today. The appearance in the late 1990s of high-speed external interfaces such as Universal Serial Bus and IEEE 1394 (FireWire) has made external disk systems popular among regular users once again, especially for users that move large amounts of data between two or more locations, and most hard disk makers now make their disks available in external cases. The capacity of hard drives has grown exponentially over time. With early personal computers, a drive with a 20 megabyte capacity was considered large. In the latter half of the 1990's, hard drives with capacities of 1 gigabyte and greater became available. As of early 2005, the "smallest" desktop hard disk in production has a capacity of 40 gigabytes, while the largest-capacity internal drives are a half terabyte (500 gigabytes), with external drives at or exceeding one terabyte. As far as PC history is concerned, the major drive families have been Modified Frequency Modulation, Run Length Limited, Enhanced Small Disk Interface, SCSI, Advanced Technology Attachment, and now Serial ATA. MFM drives required that the electronics on the "controller" be compatible with the electronics on the card - disks and controllers had to be compatible. RLL (Run Length Limited) was a way of encoding bits onto the platters that allowed for better density. Most RLL drives also needed to be "compatible" with the controllers that communicated with them. ESDI was an interface developed by Maxtor. It allowed for faster comminication between the PC and the disk. SCSI (originally named SASI for Shugart (sic) Associates) or Small Computer System Interface was an early competitor with ESDI. When the price of electronics dropped (and because of a demand by consumers) the electronics that had been stored on the controller card was moved to the disk drive itself. This advance was known as "Independent Drive Electronics" or IDE. Eventually, IDE manufacturers wanted the speed of IDE to approach the speed of SCSI drives. IDE drives were slower because they did not have as big a cache as the SCSI drives, and they could not write directly to RAM. IDE manufacturers attempted to close this speed gap by introducing Logical Block Addressing (LBA). These drives were known as EIDE. While EIDE was introduced, though, SCSI manufacturers continued to improve SCSI's performance. The increase in SCSI performance came at a price -its interfaces were more expensive. In order for EIDE's performance to increase (while keeping the cost of the associated electronics low), it was realized that the only way to do this was to move from "parallel" interfaces to "serial" interfaces, the result of which is the SATA interface. However, as for 2005, performance of SATA and PATA disks is comparable. Fiber channel interfaces are left to discussions of server drives. ==See also== *Early IBM disk storage *Superparamagnetic effect ==External links== * The PC Guide: [http://www.pcguide.com/ref/hdd/hist-c.html A Brief History of the Hard Disk Drive] *[http://www.pcguide.com/intro/fun/bindec.htm Binary versus Decimal] *[http://www.nyx.net/~sgjoen/disk.html Multi Disk System Tuning HOWTO] *[http://www.microsoft.com/technet/archive/winntas/support/diskover.mspx Windows NT Server Resource Kit: Disk Management Basics] (See section "About Disks and Disk Organization") *[http://www.legadoassociates.com/behold.htm Behold the God Box] - Less's Law and future implications of massive cheap hard disk storage *[http://www.geekzone.co.nz/content.asp?contentid=4319 Hitachi's plans for perpendicular recording allowing 20 GB microdrives or 1 TB 3.5 inch drives] *[http://www.hitachigst.com/hdd/research/recording_head/pr/PerpendicularAnimation.html Get Perpendicular] Computer storage devices Rotating disc computer storage media Computing Computer storage media ms:Cakera keras nds:Fastplaat th:ฮาร์ดดิสก์
Hard disk
==IEC Binary Prefixes== My feeling is that all the storage capacity units in this article should be changed to the Binary_prefix#IEC_standard_prefixes for clarity. The only objection I can see to this is that the traditional usage of the metric prefixes is more widely recognized. However, I feel this is trivial since the binary abbreviations (i.e. KiB, MiB, GiB, as opposed to KB, MB, GB, respectively) are very similar to their metric counterparts, the difference will not be noticed by most readers, but it does a lot in the way of accuracy for this somewhat confusing matter. In any case, the current state of the article is inconstistant in its use of IEC binary and metric prefixes, and something should be done either way. Please post your comments either supporting or objecting to this, I didn't want to make this kind of an edit without first consulting some others. -- User:Uberpenguin 18:10, 2005 Mar 28 (UTC) ---- Hmm, would anyone be willing to create and/or add a schematic of the interior of a hard drive? I was wondering what typical random access times might be for various types of drives. I just ran a benchmark program on my HD and I was wondering how it compared to others. KM Typical current mass-market drives have ''seek'' times of around 9ms. Add just over 4ms latency to that (for a 7200 RPM drive) and you have an average access time of about 13.5ms. A seriously high-perforance drive has a seek time of under 4ms and latency of 2ms - i.e., 6ms average access. But these drives sacrifice capacity to achieve their very high performance, require a SCSI interface, and are fairly expensive. User:Tannin Tannin, any particular reason for reverting my change to an auto-generated thumbnail? There's really no reason to have separate thumbnail images anymore, and that particular image has already been listed on WP:VFD after being replaced at Computer storage. User:DopefishJustin 03:44, Apr 26, 2004 (UTC) Yes Justin. It looks terrible, and defaces a perfectly good photograph. If you want to fuzz-up an image, do it to one you took yourself. User:Tannin Mr Anon, please note that a ''hard disk'' is the ''internal part'' of a hard disk drive. The terms are not synonyms. ==MFM History== I have no idea why the article claimed that MFM was invented for floppy drives. As far as I've been able to determine, MFM was first used on the IBM 3330 in 1971. The 3330 was most certainly NOT a floppy drive. The first use of MFM for a floppy drive appears to have been the IBM 53FD drive, introduced in 1977. --User:Brouhaha 08:04, 3 Sep 2004 (UTC) == damage == There's nothing written about the damage to hard disks: we should have at least a cursory explanation of the terms MTBF (mean time before failure), bad sectors/blocks/clusters, BBR (bad block relocation), handling by software and by hardware, hot swapping, something about refurbishing... --User:Joy 14:29, 27 Sep 2004 (UTC) == == "Disk Drive Speeds and Performance" http://www.notebookreview.com/forums/topic.asp?TOPIC_ID=112 == Decimal vs Binary == It seems like the following claim is incorrect. “It is important to note that hard drive manufacturers often use the decimal definition of a gigabyte or megabyte. As a result, after the drive is installed it appears that a few gigabytes or megabytes have disappeared. In reality computers operate based upon the binary numeral system. In the decimal number system a gigabyte is 7.5% smaller than in the binary number system. The term "1.44 MB", often used to describe 1440 KB floppies (actually 1.47 MB or 1.4 MiB), introduced an anomalous definition of "megabyte" as 1 × 103 × 210 bytes (1 KKiB).” The manufacturers actually state a smaller raw capacity of their drives. That is a 30GB harddrive is actually 30GB X 1.024. The reason that the actual HD is smaller than the advertised number is because some bits are reserved for sector information and thing of the like depending on the OS that’s used. This is my take on thing. Please let me know what you think, so that we can update this article if required. :No, the text in the article is correct, if a bit innaccurate on a technicality. The issue here is actually the binary PREFIX versus the metric prefix. This is largely historical; when this first became an issue there were no binary prefixes, so 2^10 bytes was called a kilobyte since 1024 (2^10) is close enough to 1000 (10^3). However, the problem becomes more noticible when you get into the multiple gigabyte range. Most OSes report a GB as what is now called a GiB, or Gibibyte; 2^30 bytes. Hard drive manufacturers continue to use the metric definition of a GB: 10^9, which is obviously less than the binary Gibibyte, because it makes it seem like the drive has a higher capacity than it actually does. :The blocks used for partition and file system accounting information rarely occupy more than a few KiB, and is utterly insignificant when talking about discrepencies of tens of Gibibytes. I'll edit this section of the article to be a little more clear. -- User:Uberpenguin 15:16, 2005 Apr 4 (UTC) == perpendicular recording == Does anybody have a more detailed description of what perpendicular recording is? I checked over at Valdemar Poulsen page and i couldn't find anything about his discovery as this paragraph from the linked article asserts. "Perpendicular recording was pioneered by the late 19th century work of Danish scientist Valdemar Poulsen, who demonstrated magnetic recording with his telegraphone." [http://news.bbc.co.uk/2/hi/technology/4411649.stm] == Altitude Sensor? == "Some modern drives include flying height sensors to detect if the pressure is too low, and temperature sensors to alert the system to overheating problems." I do not believe that as of today, April 2005, there are any hard drives that have an altitude sensor as these are still to costly. Every modern drive has a temperature sensor. Channel parameters are typically adapted to the measured temperature. User:BruceSchardt == Start Stop CSS Testing == I changed the discussion of startstop or CSS testing because the statement that 50% of the drives fail at 50,000 cycles is not correct. Typical specification for a desktop harddrive is 50,000 cycles. However this is not a mean time (cycles) till failure specification. This is a specification that all drives are supposed to achieve without failure. In typical testing a population of several hundred drives are contact-start-stop (CSS) tested for >100,000 cycles. No failures caused by the head-disk interface are allowed at less then 50,000 cycles. Testing for more then 50,000 cycles insures that the HDI design has margin. In proof, the Maxtor Diamondmax 10 hardrive specifies Start-Stop cycles at >50,000 min.[http://www.maxtor.com/_files/maxtor/en_us/documentation/data_sheets/diamondmax_10_data_sheet.pdf] Notebook hard drives are all load-unload designs that never park the heads on the disk, instead the heads are unloaded onto a ramp. This is done to increase the magnitude of non-operational shock that the drive can withstand. User:BruceSchardt
See other meanings of words starting from letter:
H
HA | HB | HC | HD | HE | HF | HG | HI | HJ | HK | HL | HM | HN | HO | HP | HR | HS | HT | HU | HW | HX | HY | HZ |Words begining with Hard_disk:
Hard-disk
Hard-disk_recording
Hard_Disk
Hard_disk
Hard_disk
Hard_disks
Hard_disk_controller
Hard_disk_drive
Hard_disk_drives
Hard_disk_drive_functioning
Hard_disk_drive_partition
Hard_disk_drive_partitioning
Hard_disk_drive_partitioning
Hard_disk_platter
Hard_disk_platter
Hard_disk_recorder
Hard_disk_recording
These materials are based on Wikipedia and licensed under the GNU FDL
YouTube.com videos better site than Turbo Tax 2007
